Cabletron Systems 7H02-06 User's Guide

7H02-06 Fast Ethernet SmartSWITCH ™ Interface Module User’s Guide 9031924

1-2Introduction 1.2 THE 7H02-06 MODULE The 7H02-06 Module provides six Fast Ethernet ports via 5 RJ45 connectors and one FEPIM. The 7H02-06 Module c

Introduction1-3 Figure 1-1. 7H02-06 Module 1.2.2 7C03 MMAC SmartSwitch, the 7C04 Workgroup SmartSwitch and the 7C04-R Workgroup SmartSwitch The 7H0

1-4Introduction Ring to be used with the 7H02-06 Module. These modules provide the capability to share data without the use of external bridges or ro

Introduction1-5 1.3.2 FEPIMs The front panel connections are standard Cabletron FEPIMs. Currently, the 7H02-06 supports the following two FEPIMs: •

1-6Introduction 1.4 RELATED MANUALS The manuals listed below should be used to supplement the procedures and other technical data provided in this m

2-1 CHAPTER 2 NETWORK REQUIREMENTS Before installing Cabletron Systems 7H02-06 Module, review the network requirements outlined in this chapter. All

2-2Network Requirements Transmitter power parameters are listed in Table 2-2.The link distance is up to 2 kilometers on the multimode fiber-optic cabl

Network Requirements2-3 The link distance is up to 100 meters on unshielded Category 5 twisted pair cable as specified by ANSI TP-PMD. Table 2-3. FE

2-4Network Requirements

3-1 CHAPTER 3INSTALLATION This chapter contains instructions for unpacking and installing the 7H02-06 Module in the 7C03, 7C04, 7C04-R MMAC SmartSwi

3-2Installation Figure 3-1. Module Bottom View 3. Remove the blank front cover over the FEPIM slot.4. Install the FEPIM as shown in Figure 3-2. Ensu

Installation3-3 Figure 3-2. Installing an FEPIM 3.3 INSTALLING/REMOVING THE 7H02-06 MODULE The 7H02-06 Module is installed in: the 7C03 MMAC SmartS

3-4Installation 1. Remove the blank panel covering the slot in which the module will be installed. All other slots in the 7C03 must remain covered t

Installation3-5 3.3.2 Removing the 7H02-06 Module from a 7C03 MMAC SmartSwitch To remove the 7H02-06 Module from a 7C03 MMAC SmartSwitch, follow the

3-6Installation 3.3.3 Installing the 7H02-06 Module in a 7C04 or 7C04-R Chassis To install the 7H02-06 Module in a 7C04 or 7C04-R Chassis, follow th

Installation3-7 Figure 3-5. Installing the 7H02-06 Module in the 7C04 Workgroup SmartSwitchFigure 3-6. Installing the 7H02-06 Module in the 7C04-R

3-8Installation 3.3.4 Removing the 7H02-06 Module from a 7C04 or 7C04-R Chassis To remove the 7H02-06 Module from a 7C04 or 7C04-R Chassis, follow t

Installation3-9 Figure 3-8. Removing the 7H02-06 Module from the 7C04-R Workgroup SmartSwitch.XXX -XXX-XXXXXX -XXX-XXX4321ScrewsEjector Tabs

3-10Installation

4-1CHAPTER 4TROUBLESHOOTINGThe 7H02-06 Module uses LANVIEW, Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW L

Noticei NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

4-2TroubleshootingTable 4-1 indicates the state of the receive port.Table 4-2 indicates the state of the transmit port.Table 4-1. Port Receive LEDsL

5-1CHAPTER 5TECHNICAL SPECIFICATIONSThis chapter includes the technical specifications for Cabletron Systems 7H02-06 module. Cabletron Systems reserve

5-2Technical Specifications• VCCI Class I5.5 IMMUNITYThe 7H02-06 Module meets the requirements of EN50082-1 including:• IEC 801-2 ESD• IEC 803-1 radia

Technical Specifications5-35.8.3 EnvironmentalOperating Temperature +5° to +40° C (+41° to +104° F)Storage Temperature -30° to +80° C (-22° to +160° F

5-4Technical Specifications

A-1APPENDIX AThe 7H02-06 module uses Fast Ethernet Interface Modules (FEPIMs) to provide front panel cable connections. The FEPIMs are user-installabl

A-2Figure A-2. FE-100FXThe transmitter power levels listed in Table A-1 are peak power levels after optical overshoot. A peak power meter must be use

Noticeii FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

Noticeiii brouillage radioélectrique édicté par le ministère des Communications du Canada. VCCI NOTICE This equipment is in the 1st Class Category (i

Noticeiv EXCLUSION OF WARRANTYAND DISCLAIMER OF LIABILITY 1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Ca

v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ...1-11.2 THE 7H02-0

viContents 5.3 SAFETY.......5-15.4 EMI ...

1-1 CHAPTER 1INTRODUCTION Welcome to Cabletron Systems 7H02-06 Fast Ethernet SmartSwitch ™ Interface Module Installation Guide. This guide is a sim