Cabletron Systems CyberSWITCH CSX202 Installation Guide

CSX200 CyberSWITCHInstallation Guide 90327532012 01

Contents viii CSX200 Installation Guide APPENDIX C FCC PART 68 - USER’S INFORMATION FOR CSX200APPENDIX D GLOSSARYINDEX

CSX200 Installation Guide 1-1 1 Introduction Welcome to the Cabletron Systems CSX200 CyberSWITCH Installation Guide . This guide provides configurati

Chapter 1: Introduction1-2 CSX200 Installation Guide Chapter 5 , Troubleshooting , shows how to use the LANVIEW LEDs on the CSX200 for network trou

Document Conventions CSX200 Installation Guide 1-3 Document Conventions The following conventions are used throughout this guide:NOTE Note symbol. C

Chapter 1: Introduction1-4 CSX200 Installation Guide Getting Help If you need additional support related to this device, or if you have any question

CSX200 Installation Guide 2-1 2 About the CSX200 The CSX200 CyberSWITCH ( Figure 2-1 ) is an access device that provides Ethernet Local Area Network

Chapter 2: About the CSX2002-2 CSX200 Installation Guide • The WPIM-SY provides a synchronous serial connection of up to 2.048 Mbps to external comm

Remote Management CapabilitiesCSX200 Installation Guide 2-3Polarity Detection and Correction — Each twisted pair port on the CSX200 incorporates a Pol

Chapter 2: About the CSX2002-4 CSX200 Installation GuideCSX200 Firmware SupportThe CSX200 firmware supports IEEE 802.1d bridging, and IP and IPX routin

CSX200 Firmware SupportCSX200 Installation Guide 2-5Firmware Data CompressionThe STAC Electronics Stacker LZS Compression algorithm provides a minimum

Chapter 2: About the CSX2002-6 CSX200 Installation GuideThis is done to replace the hidden local IP addresses from the sub network with one or more pu

CSX200 Firmware SupportCSX200 Installation Guide 2-7The ANSI standard defines a mechanism for the network to signal the existence of congestion, called

Chapter 2: About the CSX2002-8 CSX200 Installation GuideFull-duplex operation places an additional step to half-duplex operation that mirrors the oper

CSX200 Firmware SupportCSX200 Installation Guide 2-9The CSX200 supports one ISDN BRI line and either or both of the B channels for transferring data.

Chapter 2: About the CSX2002-10 CSX200 Installation GuideIn transparent bridging, the decision to forward the frame is based on this comparison. If th

CSX200 Firmware SupportCSX200 Installation Guide 2-11The CSX200 uses the Spanning Tree Algorithm to prevent data loops and duplicate data. This is a s

Chapter 2: About the CSX2002-12 CSX200 Installation GuideSystem PasswordsYou can control access to the CSX200 by the use of three passwords. Each pass

CSX200 Firmware SupportCSX200 Installation Guide 2-13• Frame Relay DTE MIB RFC1490• Security MIB RFC1472 (CCP, PAP, and CHAP)• RS-232 MIB RFC1317• LQM

Chapter 2: About the CSX2002-14 CSX200 Installation GuideIP Events, continued:• IP has detected Link UP on interface #• IP has detected Link DOWN on i

CSX200 Firmware SupportCSX200 Installation Guide 2-15• IPX has detected Port UP (WAN devices only)• IPX has detected Port DOWN (WAN devices only)• IPX

CSX200 Installation Guide i Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this docu

Chapter 2: About the CSX2002-16 CSX200 Installation Guide

CSX200 Installation Guide 3-1310BASE-T LAN RequirementsThis chapter contains general networking guidelines for setting up a 10BASE-T Local Area Networ

Chapter 3: 10BASE-T LAN Requirements3-2 CSX200 Installation GuideTemperature — Multi-pair PVC 24 AWG telephone cable typically has an attenuation of a

10BASE-T LAN ConfigurationCSX200 Installation Guide 3-310BASE-T LAN ConfigurationThis section contains the procedures for connecting a UTP segment from

Chapter 3: 10BASE-T LAN Requirements3-4 CSX200 Installation Guide3. Verify that a Link exists by checking that the receive port (RCV) LED is on (flash

CSX200 Installation Guide 4-14InstallationThis chapter shows you how to connect your CSX200 to the network. Ensure that the network meets the guidelin

Chapter 4: Installation4-2 CSX200 Installation GuideRemoving the CSX200 CoverThe cover must be removed to install a WAN Port Interface Module.To remov

Installation GuidelinesCSX200 Installation Guide 4-3Figure 4-1 Removing the Plastic Chassis CoverInstalling a WPIMTo install a WPIM into the CSX200,

Chapter 4: Installation4-4 CSX200 Installation GuideFigure 4-2 Installing WPIMsTo install a WPIM, follow these instructions:• Attach the disposable g

COMP/ENCR Module InstallationCSX200 Installation Guide 4-5COMP/ENCR Module InstallationTo install the CSX200-COMP/ENCR into the CSX200 chassis, perfor

Notice ii CSX200 Installation Guide VCCI Notice This is a Class A product based on the standard of the Voluntary Control Council for Interference by

Chapter 4: Installation4-6 CSX200 Installation GuideFigure 4-3 CSX200-COMP/ENCR Module InstallationInstalling the CSX200The CSX200 may be installed o

Rackmount InstallationCSX200 Installation Guide 4-7Figure 4-4 Tabletop or Shelf InstallationRackmount InstallationCabletron Systems offers an accesso

Chapter 4: Installation4-8 CSX200 Installation GuideMaterials RequiredThe following parts are included in the CSX200-ACCY-KIT.• Strain-relief bracket

Rackmount InstallationCSX200 Installation Guide 4-9Figure 4-6 Attaching the Strain-Relief BracketAttaching the Rackmount BracketsRefer to Figure 4-7,

Chapter 4: Installation4-10 CSX200 Installation GuideInstalling the CSX200 in a 19-Inch RackInstall the CSX200 in a 19-inch rack as follows:• Position

CSX200 Installation Guide 5-15TroubleshootingUse this chapter in conjunction with the LANVIEW status monitoring and diagnostic LEDs on the CSX200 to d

Chapter 5: Troubleshooting5-2 CSX200 Installation GuideTable 5-2 CSX200 LAN LED StatesLED Color StateReceive (RCV)OFF Not receiving trafficAMBER (flashi

TroubleshootingCSX200 Installation Guide 5-3Table 5-4 CSX200 WAN LED States for STS 1WPIM Color StateT1, DI, and E1OFF Normal or port disabledRED Red

Chapter 5: Troubleshooting5-4 CSX200 Installation GuideTroubleshooting CSX200 HardwarePower (PWR) LED is OFF• Check that the power connection is firmly

Troubleshooting the WANCSX200 Installation Guide 5-5Troubleshooting the WANLink (LNK) LED is OFFThe WAN interface is not configured for operation.• Use

Notice CSX200 Installation Guide iii Exclusion of Warranty and Disclaimer of Liability 1. EXCLUSION OF WARRANTY. Except as may be specifically provi

Chapter 5: Troubleshooting5-6 CSX200 Installation GuideWPIM-SYNC Installed in CSX200The port is operating normally. If it is not, and this LED is OFF

Troubleshooting the WANCSX200 Installation Guide 5-7WPIM-HDSL Installed in CSX200WPIM-HDSL is configured for either Full or Fractional T1 and the WPIM

Chapter 5: Troubleshooting5-8 CSX200 Installation GuideWPIM-HDSL is installed in CSX200The Port is operating normally, Loop 1 has synchronized with th

Troubleshooting the WANCSX200 Installation Guide 5-9• Verify the use of proper cabling for the HDSL connections. Category 3 or Category 5 Unshielded T

Chapter 5: Troubleshooting5-10 CSX200 Installation GuideTest (TST) LED is AMBER (blinking)The device is in test mode.• The CSX200 is running its Power

Investigating Software Configuration ProblemsCSX200 Installation Guide 5-11If TCP/IP Routing, • Check that TCP/IP Routing is set on and is enabled at

Chapter 5: Troubleshooting5-12 CSX200 Installation Guide

CSX200 Installation Guide A-1AWPIM Cable SpecificationsWPIM-T1This section provides the Cabletron Systems part number and connector specifications for W

Appendix A: WPIM Cable SpecificationsA-2 CSX200 Installation GuideTable A-3 provides RJ48 DTE pin assignments.Table A-4 provides RJ48 network pin assi

WPIM-SYCSX200 Installation Guide A-3WPIM-SYThis section provides the Cabletron Systems part number and connector specifications for the WPIM-SY interfa

Notice iv CSX200 Installation Guide Declaration of Conformity Application of Council Directive(s): 89/336/EEC73/23/EEC91/263/EEC Manufacturer’s Name:

Appendix A: WPIM Cable SpecificationsA-4 CSX200 Installation GuideEIA-449Table A-6 shows the connector number, cable assembly description, and connect

WPIM-SYCSX200 Installation Guide A-5V.35Table A-8 shows the connector number, cable assembly description, and connector type.Table A-9 provides pin as

Appendix A: WPIM Cable SpecificationsA-6 CSX200 Installation GuideDBDTETransmit Signal Timing A15EYTransmitter Signal Timing ADTE114Transmit Signal Ti

WPIM-SYCSX200 Installation Guide A-7EIA-232Table A-10 shows the connector number, cable assembly description, and connector type. Table A-11 provides

Appendix A: WPIM Cable SpecificationsA-8 CSX200 Installation GuideX.21Table A-12 shows the connector number, cable assembly description, and connector

WPIM-SYCSX200 Installation Guide A-9EIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT ATable A-14 shows the connector number, cable assembly descri

Appendix A: WPIM Cable SpecificationsA-10 CSX200 Installation GuideDBDTETransmit Signal Timing A 15E15Transmit Signal Timing ADTEDBTransmit Signal Tim

WPIM-DDSCSX200 Installation Guide A-11WPIM-DDSThis section provides Cabletron Systems part number and connector specifications for the WPIM-DDS interfa

Appendix A: WPIM Cable SpecificationsA-12 CSX200 Installation GuideWPIM-E1This section provides the Cabletron Systems part number and connector specifi

WPIM-E1CSX200 Installation Guide A-13Table A-20 provides WPIM-E1 DTE interface cable pin assignments.Table A-21 provides WPIM-E1 RJ45 network interfac

CSX200 Installation Guide v Contents CHAPTER 1 INTRODUCTIONRelated Documentation ...

Appendix A: WPIM Cable SpecificationsA-14 CSX200 Installation GuideWPIM-DIThis section provides Cabletron Systems part number and connector specificati

WPIM-HDSLCSX200 Installation Guide A-15Table A-24 provides the WPIM-DI drop and insert interface cable pin assignments.WPIM-HDSLThis section provides

Appendix A: WPIM Cable SpecificationsA-16 CSX200 Installation Guide

CSX200 Installation Guide B-1BSpecifications and Standards ComplianceThis chapter contains hardware specifications, and safety and compliance standards

Appendix B: Specifications and Standards ComplianceB-2 CSX200 Installation GuideCSX200 Regulatory ComplianceSafety — This unit meets the safety requir

Individual WPIM Regulatory ComplianceCSX200 Installation Guide B-3WPIM-SYThis section describes the environmental specifications and safety and approva

Appendix B: Specifications and Standards ComplianceB-4 CSX200 Installation GuideWPIM-E1This section describes the environmental specifications and safe

CSX200 Installation Guide C-1CFCC Part 68 - User’s Information for CSX200The following instructions are to ensure compliance with the Federal Communic

Appendix C: FCC Part 68 - User’s Information for CSX200C-2 CSX200 Installation Guide6. If the telephone company alters their equipment in a manner tha

FCC Part 68 - User’s Information for CSX200CSX200 Installation Guide C-3AFFIDAVIT FOR THE CONNECTION OFCUSTOMER EQUIPMENTTO 1.544 MBPS AND/OR SUBRATE

Contents vi CSX200 Installation Guide CHAPTER 3 10BASE-T LAN REQUIREMENTSNetwork Requirements ...

Appendix C: FCC Part 68 - User’s Information for CSX200C-4 CSX200 Installation GuideI attest that the operator(s) maintainer(s) of the digital CPE res

CSX200 Installation Guide D-1DGlossary10BASE-T — IEEE 802.3 standard for the use of Ethernet LAN technology over Unshielded Twisted Pair wiring, runni

Appendix D: GlossaryD-2 CSX200 Installation GuideDHCP — Dynamic Host Configuration Protocol is a protocol for automatic TCP/IP configuration that provid

GlossaryCSX200 Installation Guide D-3ISDN — Integrated Services Digital Network. Digital transmission standard defining communication protocols permitt

Appendix D: GlossaryD-4 CSX200 Installation GuideOSI — Open System Interconnection. An international standard developed by ITU (formally CCITT) and IS

GlossaryCSX200 Installation Guide D-5SNMP — Simple Network Management Protocol. A widely implemented Internet network management protocol that allows

Appendix D: GlossaryD-6 CSX200 Installation GuideWatchdog Frames — Frames sent out by servers to clients, under IPX, to verify that clients are still

CSX200 Installation Guide Index-1IndexNumerics10BASE-Tconnection 3-3impedance 3-1length 3-1requirements 3-1temperature 3-2BBridge filtering 2-11Bridgin

IndexIndex-2 CSX200 Installation GuideRRack Mountingaccessory kit 2-3Remote Network Management 2-3Routing 2-10SSafety Requirements B-3SNMP 2-12SNMP Co

Contents CSX200 Installation Guide vii Status 1 (STS1) LED is AMBER ................5-7Status 1 (STS1