SmartSwitch 90009C214-2 DC Power SupplyInstallation Guide 9031305-05
Introduction1-2 Figure 1-1. The 9C214-2 Power Supply9C214-2100%50%0%LoadPOWER SUPPLY MODULESTATUSPWRSNBTHIS UNIT TO BEINSTALLED IN ARESTRICTED ACCESS
1-3Introduction Features Diagnostic Controller for Management Each 9C214-2 Power Supply has a diagnostic controller. This diagnostic controller inclu
Introduction1-4 Power Distribution System The SmartSwitch 9000 uses a distributed DC power system (Figure 1-2) similar to those used in super compute
1-5Introduction Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual.Smar
Introduction1-6
2-1 Chapter 2 Installing the 9C214-2 Power Supply At least one power supply must be installed on the rear of the SmartSwitch 9000 chassis. Additional
Installing the 9C214-2 Power Supply2-2 5. Remove the cover. (Keep the cover in the event you need to remove the power supply. The cover must be repla
2-3Installing the 9C214-2 Power Supply Figure 2-1. Installing the 9C214-2 Power Supply21...9C214-2100%50%0%LoadPOWER SUPPLY MODULE
Installing the 9C214-2 Power Supply2-4 Connecting Power Source A nominal 48 or 60 volt positive or negative power source can be connected to a 9C214-
2-5Installing the 9C214-2 Power Supply Connecting a Nominal -48/-60 Volt Negative Power Source The nominal -48/-60 volt negative power source is conn
Installing the 9C214-2 Power Supply2-6 Powering Up a 9C214-2 Power Supply 1. Turn on the 9C214-2 Power Supply using the circuit breaker at the bottom
3-1 Chapter 3 9C214-2 Power Supply Operation The 9C214-2 Power Supply can operate with input voltages ranging from36 – 72 positive or negative Volts
9C214-2 Power Supply Operation3-2 Diagnostic Controller The diagnostic controller is composed of a Z-80 microprocessor and it’s supporting logic. The
3-39C214-2 Power Supply Operation Figure 3-1. 9C214-2 Power Supply LANVIEW LEDs The PWR Status LED indicates, by color, the status of a power supply’
9C214-2 Power Supply Operation3-4 The SMB Status LED indicates, by color, the status of the diagnostic controller. The possible colors, states, and d
3-59C214-2 Power Supply Operation The Power Supply Level Indicator LED indicates, by segment number, the percentage of the power supply’s capacity be
9C214-2 Power Supply Operation3-6
4-1 Chapter 4 Specifications Safety The 9C214-2 Power Supply, when properly installed on the SmartSwitch 9000 Chassis, complies with the following spe
Specifications4-2 Service The 9C214-2 Power Supply is designed with the following service capability: MTBF (MIL-STD-217): >200,000 hours projected
4-3Specifications DC Input Each 9C214-2 Power Supply operates with the following voltage and current. Voltage 36–72 VDC Current 30A DC Maximum Fusing
iNotice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n
Specifications4-4
Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not
iiiNotice DECLARATION OF CONFORMITYADDENDUM Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Man
Noticeiv
v Contents Chapter 1 Introduction Using This Manual...
Contentsvi
1-1 Chapter 1 Introduction Using This Manual Read through this manual to become familiar with its contents and gain an understanding of the features
Comments to this Manuals