Cabletron-systems 9F120-08 User Manual

SmartSwitch 90009F120-08, 9F122-12 & 9F125-08User’s Guide 9031174-02

Introduction1-2 Connectivity The front panel Master port connections are via standard fiber FDDI MIC connectors or RJ-45 Unshielded Twisted Pair ports

1-3Introduction Figure 1-1. The Concentrator ModulesM1M2M3M4M5M6M7M815648237FDDISMBCPUFNB9F120-08FDDISMBCPUFNB9F122-12FDDI14235687M1M2M3M4M5M6M7M8156

Introduction1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual.Smar

2-1 Chapter 2 Installing the MicroLAN Modules SmartSwitch 9000 MicroLAN Modules can be installed in any of the 14 slots that are available. To instal

Installing the MicroLAN Modules2-2 Figure 2-1. Installing the MicroLAN ModuleMetal Back-PanelModule GuidesModuleJack for ESDWrist StrapPlastic TabWar

2-3Installing the MicroLAN Modules The Reset Switch The Reset switch is located on the front panel, under the top plastic tab, as shown in Figure 2-2

Installing the MicroLAN Modules2-4 User-Accessible Components Figure 2-3 shows the various components that are accessible to the user. These consist

2-5Installing the MicroLAN Modules Setting the Module Card DIP Switch An eight-switch DIP switch is located on the module card, as shown in Figure 2-

Installing the MicroLAN Modules2-6 See the Cautions at the end of this table. Table 2-1. Function of DIP Switch Switch Function Description 8Clear

3-1 Chapter 3 Operation The MicroLAN Modules, as shown in Figure 3-1, provide concentrator ports that connect directly to the FNB bus. Each port can

Operation3-2 System Management Buses There are two management channels within the SmartSwitch 9000 system: the SMB-1 and the SMB-10. These buses prov

3-3Operation System Diagnostic Controller This diagnostic controller is composed of a Z-80 microprocessor and its supporting logic. The diagnostic co

Operation3-4

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figu

LANVIEW LEDs4-2 The functions of the System Management Bus (SMB) and the CPU LEDs are listed in Table 4-1.The functions of the FNB Receive LEDs are l

4-3LANVIEW LEDs There is one FDDI Port LED for each Master port. The functions of the FDDI Port LEDs are listed in Table 4-4. Table 4-4. FDDI Status

LANVIEW LEDs4-4

5-1 Chapter 5 Specifications Safety This equipment meets the following safety requirements:• UL 1950• CSA C22.2 No. 950 • EN 60950• IEC 950• EMI Requi

Specifications5-2 Physical Dimensions: 35.0 D x 44.0 H x 3.0 W centimeters(13.8 D x 17.4 H x 1.2 W inches) Weight: Unit: 1360.7 gr. (3 lb)Shipping:

iNotice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

iiiNotice DECLARATION OF CONFORMITYADDENDUM Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Man

Noticeiv Safety Information CLASS 1 LASER TRANSCEIVERSThe 9F120-08, 9F122-12 and 9F125-08 are Class 1 Laser ProductsThe 9F120-08, 9F122-12 and 9F125-

v Contents Chapter 1 Introduction Features...

Contentsvi

1-1 Chapter 1 Introduction The 9F120-08, 9F122-12 and 9F125-08 MicroLAN™ Modules are Dual Attached Concentrator modules for the SmartSwitch 9000 (see