Cabletron Systems 7C04 Workgroup User Manual

7C04 WorkgroupSmartSWITCH ™ ChassisUser’s Guide 9031700-01

Introduction1-5 If the frame’s entry is not found in the connection table, a request is sent to the system’s Virtual Network Services (VNS). The VNS

1-6Introduction 1.5 RELATED MANUALS The following manuals supplement the procedures and other technical data provided in this manual. The procedures

2-1 CHAPTER 2INSTALLATION The 7C04 Chassis can be used as a stand-alone chassis or rack mounted in a standard 19-inch equipment rack provided ther

2-2Installation 2.2 INSTALLING THE 7C04 CHASSIS IN AN EQUIPMENT RACK The following section details the process of attaching mounting brackets to the

Installation2-3 7. Align the two round holes of the left mounting bracket with the holes (from which you removed the screws) on the left side of the

2-4Installation 2.2.2 Mounting the 7C04 Chassis To mount the 7C04 Chassis in a standard 19-inch equipment rack, (Figure 2-2) use the following steps

Installation2-5 2.3 THE 7C04 CHASSIS POWER SUPPLY MODULE The 7C04 Chassis is equipped with a removable power supply module. The power supply module

2-6Installation 3. Align the notch on the top of the power supply module with the semi-circular tab in the top center of the power supply module cav

Installation2-7 2.3.3 Powering up the Power Supply Module Note: Prior to powering up the power supply module, we recommend that you install the 7X

2-8Installation 2.3.4 Removing the Power Supply Module To remove the power supply module from the chassis, refer to Figure 2-4 and proceed as follow

Noticei NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

3-1 CHAPTER 3TROUBLESHOOTING The front panel of the power supply module of the 7C04 Chassis (Figure 3-1) contains four LANVIEW LEDs to assist you in

3-2Troubleshooting Table 3-1. POWER IN LED LED Color Indicates Action Green The power supply’s input power is acceptable. Normal Operation.No acti

Troubleshooting3-3 Table 3-3. OVERLOAD LED LED Color Indicates Action Green Normal operation No action necessary.Red The modules within the chassis

4-1 CHAPTER 4TECHNICAL SPECIFICATIONS This chapter includes the technical specifications for Cabletron Systems 7C04 Chassis. Cabletron Systems reserv

4-2Technical Specifications4.4 SERVICEMTBF: >200,000 hoursMTTR: <0.5 hour4.5 POWERAC Input: 100 - 125 volts, 3.8 amps200 - 250 volts, 1.9 amps5

Technical Specifications4-34.7 ENVIRONMENTALOperating Temperature: +5° to +40° C (+41° to +104° F)Storage Temperature: -30° to +90° C (-22° to +194° F

Noticeii FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

Noticeiii VCCI NOTICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and confor

v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ...1-11.2 USING THE

1-1 CHAPTER 1INTRODUCTION Welcome to Cabletron Systems 7C04 Workgroup SmartSwitch Chassis User’s Guide . This manual describes the physical charact

1-2Introduction 1.3 CHASSIS OVERVIEW The 7C04 Chassis (Figure 1-1) is a rack-mountable, multi-media, switching center. The chassis is a stand-alone

Introduction1-3 1.3.1 7X00 SmartSwitch Controller Module The 7X00 SmartSwitch Controller Module is the only processing and management element in the

1-4Introduction 1.3.3 Operations Data entering through a front panel of a SmartSwitch interface module in the 7C04 Chassis is converted by the modul