Cabletron Systems CSX400 User's Guide Page 118
- Page / 150
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Bridging
4-72 Fast Ethernet Port Configuration
Desired Operational Mode
Displays the operational mode that you want to conÞgure for this port. The
following operational modes are available for each port:
FE-100TX Auto-Negotiation, 10Base-T, 10Base-T Full Duplex,
100Base-TX, and 100Base-TX Full Duplex.
FE-100FX 100Base-FX and 100Base-FX Full Duplex
See Setting the Desired Operational Mode for the FE-100TX and Setting the
Desired Operational Mode for the FE-100FX, following, for more information.
Advertised Abilities
This Þeld works in conjunction with auto-negotiation on FE-100TX ports. During
auto-negotiation, the local hardware will advertise all selected modes in
descending bandwidth order: 100Base-TX Full Duplex, 100Base-TX, 10Base-T Full
Duplex, and 10Base-T.
Of the selected abilities, the highest mode available on the port on the other side
of the connection will automatically be used. The Advertised Abilities will only be
used when auto-negotiation is enabled.
Remote Capabilities
This Þeld displays the advertised abilities of the remote hardware at the other end
of the link from the FE-100TX port. Again, possible advertised abilities by the
remote partner include 10Base-T, 10Base-T Full Duplex, 100Base-TX, or
100Base-TX Full Duplex.
If auto-negotiation is not enabled or supported at either the local or remote
interface, or if there is no active link, all entries in this Þeld will be grayed out.
NOTE
Auto-negotiation is not available on the FE-100FX; therefore, the Advertised Abilities
and Remote Capabilities section of the Fast Ethernet ConÞguration window will be
grayed out when you are viewing the port conÞguration of an FE-100FX.
!
CAUTION
If you choose to select a speciÞc mode of operation (rather than auto-negotiation), you
should be sure that the link partner supports the same mode. Otherwise, no link will be
achieved.
If you select a full duplex mode and the link partner supports the same wire speed but not
full duplex, a link will be achieved, but it will be unstable and will behave erratically.
If you select auto-negotiation, the local node will try to match the mode of the link partner,
even if the link partner is not set to auto-negotiate, and even if the local node must use a
mode which it is not currently advertising.
- CSX200 and CSX400 1
- User’s Guide 1
- Virus Disclaimer 3
- Restricted Rights Notice 5
- Chapter 4 Bridging 8
- Contents 10
- Introduction 11
- HSIM-W6 and HSIM-W84 12
- Related Manuals 13
- Software Conventions 14
- Using the Mouse 15
- Using Window Buttons 16
- Getting Help 17
- CSX200 and CSX400 Firmware 18
- CSX200 and 400 Chassis View 19
- Viewing Chassis Information 20
- Front Panel Information 21
- Menu Structure 22
- The Chassis Manager Window 27
- Viewing Hardware Types 28
- Managing the Device 29
- 2-12 Managing the Device 30
- Managing the Device 2-13 31
- 2-14 Managing the Device 32
- Managing the Device 2-15 33
- 2-16 Managing the Device 34
- Managing the Device 2-17 35
- (Received only) 35
- (Received only) 35
- (Transmit only) 35
- Enabling and Disabling Ports 36
- Managing the Device 2-19 37
- 2-20 Managing the Device 38
- WAN Configuration 39
- About the CSX400 40
- CSX WPIMs 41
- 3-4 CSX WPIMs 42
- WAN Logical View 43
- Changing WAN Logical Settings 44
- WAN Logical View 3-7 45
- 3-8 WAN Logical View 46
- About Transparent Bridging 48
- About Source Route Bridging 48
- Bridging Basics 4-3 49
- 4-4 Bridging Basics 50
- Bridging Basics 4-5 51
- The Bridge Status Window 54
- The Bridge Status Window 4-9 55
- 4-10 The Bridge Status Window 56
- The Bridge Status Window 4-11 57
- 4-12 The Bridge Status Window 58
- The Bridge Status Window 4-13 59
- Bridge Statistics 61
- 4-16 Bridge Statistics 62
- Bridge Statistics 4-17 63
- 4-18 Bridge Statistics 64
- Bridge Statistics 4-19 65
- 4-20 Bridge Statistics 66
- Bridge Statistics 4-21 67
- 4-22 Bridge Statistics 68
- The CSMACD Statistics Window 69
- 4-24 Bridge Statistics 70
- Bridge Statistics 4-25 71
- 4-26 Bridge Statistics 72
- Bridge Statistics 4-27 73
- 4-28 Bridge Statistics 74
- Bridge Statistics 4-29 75
- 4-30 Bridge Statistics 76
- Bridge Statistics 4-31 77
- Source Route Statistics 78
- Bridge Statistics 4-33 79
- 4-34 Bridge Statistics 80
- Bridge Spanning Tree 81
- Bridge Level Fields 82
- Bridge Spanning Tree 4-37 83
- Bridge Port Level Fields 84
- Bridge Spanning Tree 4-39 85
- 4-40 Bridge Spanning Tree 86
- Bridge Spanning Tree 4-41 87
- Filtering Database 88
- Filtering Database 4-43 89
- 4-44 Filtering Database 90
- Filtering Database 4-45 91
- 4-46 Filtering Database 92
- Filtering Database 4-47 93
- 4-48 Filtering Database 94
- Bridging 100
- Changing the Receive Ports 101
- Source Route Configuration 103
- Information on Source Routing 104
- Making and Setting Changes 109
- Setting the Aging Time 111
- Duplex Modes 112
- The Duplex Modes Window 113
- 4-68 Duplex Modes 114
- Duplex Modes 4-69 115
- SONET Port Configuration 120
- SONET Port Configuration 4-75 121
- SONET/SDH Statistics Window 122
- 4-78 SONET Port Configuration 124
- SONET Port Configuration 4-79 125
- 4-80 SONET Port Configuration 126
- SONET Port Configuration 4-81 127
- Token Ring Bridge Mode 129
- Defining the Bridge Modes 130
- Defining the Bridge Method 136
- Setting the Bridge Method 137
- Configuring SmartTrunking 142
- Configuring SmartTrunking 4-97 143
- 4-98 Configuring SmartTrunking 144
- Configuring SmartTrunking 4-99 145
Related products and manuals for Networking Cabletron Systems CSX400
(74 pages)
(310 pages)© 2020, manymanuals.com. All rights reserved. | 1.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals